河北瑞博橡塑制品有限公司

咨詢電話：131 6657 0872

制作預埋鍍鋅角鋼 →混凝土澆筑→安裝橡膠止水條（下墊高分子密封膩脂防水層）→安裝鍍鋅槽鋼→安裝63×40×4 M16螺栓加固→縫上口安置鋼板
Making pre ded galvanized steel angle, pouring concrete, installing rubber water stop bar (lower polymer sealing grease waterproof layer), installing zinc plated channel steel, installing 63 * 40 * 4 M16 bolt reinforcement, and placing steel plate on seam top

結構施工時的橡膠止水帶或金屬止水環按常規施工，施工過程嚴格按規范及工藝要求施工確保這一道防水層能**達到止水效果，變形縫兩側預埋L63×6角鋼，底板處預埋角鋼底邊每格50cm開直徑30mm圓孔，開孔保證兩側有15mm的邊，開孔方便采用小型振動棒插入，保證角鋼底部的密實；結構錨栓M16@150，通絲與角鋼連接，主體封頂，沉降基本均勻后變形縫縫內進行丙凝注漿，丙凝是由丙烯酰胺、亞甲、過硫酸胺、三乙醇胺等溶液組成，它能在瞬間止水，具有柔韌性、遇水膨脹等特性，在丙凝防水層外加一道高分子密封膩?zhàn)臃浪畬樱四佔泳哂辛阆?0度，零上100度不變形與混凝土、橡膠、塑料及各種金屬材料緊密粘貼止水密封**外側加一道可卸式止水帶，在預埋角鋼面層均勻鋪設高分子密封膩脂層，蓋上橡膠止水帶，壓上槽鋼，然后對螺栓進行緊固**可以了，縫口均需用鋼板封口，避免人為破壞防水層。
The construction of the structure of the rubber sealing belt or metal sealing ring according to the conventional construction, the construction process strictly according to the standards and process requirements to ensure that the construction of the road waterproof layer ** can achieve the sealing effect, deformation on both sides of the joint ded L63 * 6 angle, bottom plate pre buried bottom angle of each grid 50cm 30mm diameter hole, hole guarantee 15mm the two side holes, convenient using small vibration rod insertion, ensure angle at the bottom of the dense structure; anchor bolt M16@150, harness and connection, the main cap, settlement within the acrylamide grouting seam deformation evenly, acrylamide is composed of acrylamide and methylene, ammonium persulfate, triethanolamine solution etc. it can, in an instant sealing, with flexibility, water swellable properties, a polymer layer with a waterproof sealing putty in acrylamide waterproof layer, the putty has 20 degrees, 100 degrees above zero deformation With concrete, rubber, plastic and metal materials integrated with the seal, the lateral and a detachable sealing strip, in the pre buried angle surface evenly distributed fat layer polymer sealing cover, rubber sealing strip, the pressure on the channel, and then the bolt fastening can, the seam is required with steel plate to avoid the destruction of the waterproof layer sealing.